installation:adc:dryer
Differences
This shows you the differences between two versions of the page.
|
installation:adc:dryer [2019/02/13 17:07] maxish |
installation:adc:dryer [2020/08/24 16:07] (current) maxish |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ===== ADC Dryers ===== | ===== ADC Dryers ===== | ||
| - | There are many variants of ADC dryers models. The connections to all of them are all similar. | + | There are many variants of ADC dryers models. The connections to all of them are similar. |
| ====== Parts ====== | ====== Parts ====== | ||
| * Reader | * Reader | ||
| - | * Cable harness (3-wire or 4-wire) | + | * Cable harness |
| + | * Power supply (for Phase 5 controls only) | ||
| Line 10: | Line 11: | ||
| - Before proceeding, you should assign numbers to each of the machines in the laundry room/building. It is highly recommended that you place labels on each machine. \\ \\ | - Before proceeding, you should assign numbers to each of the machines in the laundry room/building. It is highly recommended that you place labels on each machine. \\ \\ | ||
| - | - Set the machine type and number using the DIP switch on the MCU circuit board: {{:installation:wascomat:pasted:20170708-141522.png}}\\ See [[installation:dip_switch|DIP switch settings page]] to understand how to configure DIP switch positions to set the machine type (washer or dryer) and number. Note that MCUs may already come from Mitech configured with the appropriate DIP switch settings. Proceed with installing the MCU on the corresponding machine type and number. \\ \\ | + | - Set the machine type and number using the DIP switch on the reader circuit board: {{:installation:wascomat:pasted:20170708-141522.png}}\\ See [[installation:dip_switch|DIP switch settings page]] to understand how to configure DIP switch positions to set the machine type (washer or dryer) and number. |
| - Turn machine power OFF! \\ \\ | - Turn machine power OFF! \\ \\ | ||
| - Remove the coin-drop \\ \\ | - Remove the coin-drop \\ \\ | ||
| - | - If the dryer's control board has the white headers show below, plug the two mating connectors of the provided cable harness into the connectors shown in red (one is power, one is coin signal) \\{{:installation:adc:pasted:20190213-165537.png}} \\ \\ | + | - If the dryer has a Phase 7 control board (with the white headers) shown below, plug the two mating connectors of the provided cable harness into the connectors shown in red (one is power, one is coin signal) \\{{:installation:adc:pasted:20190213-165537.png}} \\ \\ |
| - | - If the dryer's control board has the red header show below, just plug the mating connector into it \\ {{:installation:adc:pasted:20190213-170335.png}} \\ | + | - If the dryer has a Phase 5 control board (with the red header shown below), just plug the mating connector into it and connect the provided power supply adapter accordingly \\ {{:installation:adc:pasted:20190213-170335.png}} \\ |
| - Mount the reader. You may need to drill a couple of holes depending on the machine | - Mount the reader. You may need to drill a couple of holes depending on the machine | ||
| ====== Vend Pricing ====== | ====== Vend Pricing ====== | ||
| Set on the Portal. Note the reader just sends a pulse and charges the vend price. The amount of time added is set on the machine. | Set on the Portal. Note the reader just sends a pulse and charges the vend price. The amount of time added is set on the machine. | ||
installation/adc/dryer.txt · Last modified: 2020/08/24 16:07 by maxish
Page Tools
